Car stereo amplifier circuit using TDA2040

admin February 10, 2011 22 Comments

Car Audio Amplifier Circuit:

Given below is a car stereo amplifier circuit using  audio amplifier IC – TDA2040

Description of the circuit:

A car stereo amplifier circuit using TDA2040 is shown here. TDA2040 is a monolithic integrated audio amplifier that operates in Class AB mode. The IC has built in circuitry for short circuit protection and thermal shut down and more over it can be operated from a single supply too. The amplifier can deliver 12 watts into to a 8 ohm speaker.

In the circuit the IC is wired in order to operate from the cars 12V line. Capacitor C7 is the input DC decoupling capacitor and R4 provides feedback. Network consisting of resistor R5 and capacitor C5 provides high frequency stability and prevents any chance of oscillation. Capacitor C6 couples the ICs output to the speaker. C2 and C1 are power supply filters.

Circuit diagram of car stereo circuit using TDA2040

Car audio amplifier circuit schematic and diagram

Car amplifier circuit diagram

Notes.

  • Quality of the PCB is a very crucial factor in the amplifiers performance.
  • The amplifier can be operated from cars 12V line.
  • Heat sink is necessary for TDA2040.
  • All electrolytic capacitors must be rated 15V.
  • Only one channel is shown here. For stereo application you must make one more identical copy.

We have more car audio amplifier circuits in our website of your interest:

1.Car Stereo Amplifier using TDA2003

2. Car Audio Amplifier using TDA1553

Check our other popular amplifier circuits:

3. 20 Watt Audio amplifier circuit

4. 2X60 Watt Audio amplifier circuit

5. HiFi Headphone Amplifier Circuit


Comments
  • August 13, 2015

    This is an interesting circuit. Thank you for sharing this.

  • Saulius
    August 10, 2015

    Hi. In my country i can only find the capacitors rated 50v and above. Is it gonna work with them instead of 15v?

  • anirvan
    January 20, 2015

    Sir,
    I have constructed an Audio Amp Circuit using TDA2003 and TDA2030A, I want to know how much Amperes is required for Both the ICs to produce Full output i.e., 10Watts(TDA2003) and 18Watts(TDA2030A) ?
    Also Do they require Maximum operating Voltages to Output Full Power as on Datasheets?
    Kindly Reply soon
    Thanks

  • anirvan
    January 11, 2015

    How to get Full(Maximum) output from This Circuit when operating on Mains Transformer ?
    As the datasheet tells it can output 20 Watts
    How much Current in Amps will be needed to get Full 20 Watts?

  • awais mughal
    January 3, 2015

    hello sir,
    please tell me which amplifier is best “tda2003” or “tda2040” for 6 inch speaker.

    regards,
    awais mughal

  • November 27, 2014

    i made exactly the same circuit but only humming noise is at the output…i used 22k ohm instead of 20k ohm at the place of R2 also do i need a preamp for this circuit

  • Zlatko
    June 5, 2014

    Im living in Croatia and we dont have too big choice of parts so with what can I replace c5 (100nf electrolytic capacitor) please ,help me out.

    • lalu
      November 5, 2014

      You can use 0.1uf cap instead of 100nf…
      ie, 100nf=0.1uf
      😉

  • rogen
    November 28, 2013

    good day sir, i’m an engg. student. our teacher given us any amplifier project and when i see this circuit i’m planning to make this one. ahm sir what device to be use to control the volume in this circuit and where i am going to put it?.
    thank you in advance.

  • Dylan
    October 18, 2013

    Can we add a volume control on this?

    and what value of potentiometer should I use and where should connect it?

  • MICHAEL
    May 5, 2013

    Sir,
    Am a student, I designed this cct using TDA2030 but the output was very poor. It has humming sound, does not have bass at all,n does nt produce a clear sound. Pls I need ur help before tuesday, it is a project I needed to submit very very soon.

    • Seetharaman
      May 7, 2013

      Hi Michael The above circuit with TDA2030 and 12 volt supply will give an output of around 2watts into 8 ohms speaker. The quality should be good. Check C1 and C2 should be as close to the IC pin 3 & 5 as possible. the layout is critical for this amplifier to care of layout problems add 1K ohms resistance between input and C7, add 470PF ceramic disc capacitor in parallel with R6, which will solve your problem. With 4 ohms speaker you will get 4watts output. with 2 X 4 ohms speakers in parallel you will get 8 watts.

      • MICHAEL
        May 10, 2013

        Thnks for your support and help, I really appreciate it.

  • Jonathan
    May 3, 2013

    Doncraze wanted a sub amp and this ckt will make about 35 watts with a 40-45V power supply. C6 should be at least a 35V electrolytic, C2 should be at least 50V, all the other caps should be at least 25 Volts. You can also use TDA2050 or 2052; they handle slightly more voltage and power. Definately use a 8 sq in or larger heatsink. See my earlier note below. He may also want to look up ’40W amplifier using TDA1514′.

  • Vishakh
    January 4, 2013

    Good circuit. Get good output with out any noise

  • vishakh
    January 3, 2013

    i made this circuit. But the speaker doesnt works. I can find current upto c7 . C7 is in working condition. What will be the problem. I give supply using transformer

  • Shawn
    August 7, 2012

    What if the caps are rated at 16v instead of 15v?

  • Geo George
    May 5, 2012

    I was happy to find such usefull circuits that does really work, while in some other sites, i was not satisfied. I am an engg. Student and have to submit a project work. I think you can help me out by suggesting and publishing a good project usefull for E&E engg. Students within a range of Rs 10000 to 12000

  • Seetharaman
    February 17, 2012

    Hi Scotty insert a 22K Log volume control between in socket and C7.(interchange C7 polarity)

  • Scotty
    February 16, 2012

    I’m planning to build this circuit for a guitar amp. Any considerations I should take into account? Also, I plan to drive this circuit with a preamp circuit (either the ua741 on this site or a JFET one I’ve found). I’d love to have a “master volume” control added to this circuit, in order to give me the option to drive the input harder from the preamp yet keep the overall volume low. Basically creating overdrive distortion. Conversely, I’d like to be able to max the “master” volume and turn back the gain of the preamp to get a cleaner sound. Is there a reasonable way to do this or am I out of my mind?

    Thanks in advance!

    …scotty

  • Doncraze
    June 4, 2011

    Pls can some help me 50w subwoofer circuit

  • Jonathan
    March 5, 2011

    Wow. Serious overkill. TDA2040 is a high-power IC that can run at 40V supply. Just use a TDA2002/3 or LM383 and save the 2040 for 35W apps. Also, this circuit will make about 3-4 Wrms
    into 4 ohms at 12V supply. C5 can be mylar or disc, C6 can be lower; say 470u or 1000u at 10V, tho any smaller caps can limit bass output. Max Supply V is 18V with TDA2002.

Leave a Reply to vishakh Cancel reply

Your email address will not be published. Required fields are marked *