CRO-Cathode Ray Oscilloscope

jojo December 22, 2016 28 Comments

Introduction to CRO – Cathode Ray Oscilloscope

The cathode ray oscilloscope is an extremely useful and versatile laboratory instrument used for studying wave shapes of alternating currents and voltages as well as for meas­urement of voltage, current, power and frequency, in fact, almost any quantity that involves amplitude and waveform. It allows the user to see the amplitude of electrical signals as a function of time on the screen. It is widely used for trouble shooting radio and TV receivers as well as laboratory work involving research and” design. It can also be employed for studying the wave shape of a signal with respect to amplitude distortion and deviation from the normal. In true sense the cathode ray oscilloscope has been one of the most important tools in the design and development of modern electronic circuits.

Buyers Guide – We have developed an excellent buyers guide for people who are looking to buy a CRO. So here is our first guide to Buy an Analog Oscilloscope – which explains which all features to look for, compares the top selling products and much more.

Block Diagram of a CRO

CRO Block Diagram

CRO Block Diagram

The instrument employs a cathode ray tube (CRT), which is the heart of the oscilloscope. It generates the electron beam, accel­erates the beam to a high velocity, deflects the beam to create the image, and contains a phosphor screen where the electron beam eventually becomes visible. For accomplishing these tasks various electrical           signals and voltages are required, which are provided by the power supply circuit of the oscilloscope. Low voltage supply is required for the heater of the electron gun for gen­eration of electron beam and high voltage, of the order of few thousand volts, is required for cathode ray tube to accelerate the beam. Normal voltage supply, say a few hundred volts, is required for other control circuits of the oscilloscope.

Horizontal and vertical deflection plates are fitted between electron gun and screen to deflect the beam according to input signal. Electron beam strikes the screen and creates a visible spot. This spot is deflected on the screen in horizontal direction (X-axis) with constant time dependent rate. This is accomplished by a time base circuit provided in the oscilloscope. The signal to be viewed is supplied to the vertical deflection plates through the vertical amplifier, which raises the potential of the input signal to a level that will provide usable deflection of the electron beam. Now electron beam deflects in two directions, horizontal on X-axis and vertical on Y-axis. A triggering circuit is provided for synchronizing two types of deflections so that horizontal deflection starts at the same point of the input vertical signal each time it sweeps. A basic block diagram of a general purpose oscilloscope is shown in figure. Cathode ray tube and its various components will be discussed in the following Arts.

Comments
  • LALIT MOURYA
    August 10, 2015

    NICE & THANKS

  • taufeeq
    December 4, 2014

    it is very good and is better than others.

  • November 12, 2014

    IT VERY USEFUL

  • September 22, 2014

    Beautiful

  • September 22, 2014

    :-OIt is so large for practical theory.B-)But it is good for knowledge study. :-)THANK YOU;-)

  • September 9, 2014

    most thanks

  • mohith
    July 5, 2014

    thankyou

  • chitra lalawat
    April 24, 2014

    i think…delay line is responsible synchronising…

  • vinay gaur
    April 13, 2014

    it is very useful to information to me

  • suraj awatade
    February 4, 2014

    Thanque so much ..cro information is useful*

  • John
    November 21, 2013

    An oscilloscope cannot measure current or power. It measures voltage, in various forms, but it cannot measure current without using an external shunt resister and calculating it yourself, and it cannot measure power without knowing both the voltage and current.

  • vadrevu.kamesh
    November 10, 2013

    delay line basically used for delaying the input signal nearly around 80 to 200ns. you have not mentioned in it

  • vadrevu.kamesh
    November 10, 2013

    nothing given regarding function of delay line

  • Diya
    October 8, 2013

    Thank you very much it was usefull for me in understanding cro better…..

  • Navnath
    August 22, 2013

    information is very usefulto us
    thank you…………

  • SUDESH
    July 7, 2013

    a very useful study on CRO, thanks for this info

  • May 10, 2013

    me too need the complete working of cro…

  • s.magesh kumar
    February 28, 2013

    dear sir
    i need complete using procedure on cro .
    analog and digital circuits signal testing procedure via cro
    please help to me

  • December 18, 2012

    It is very useful information to me.

  • March 30, 2012

    thanx was very useful information

  • rahul
    December 27, 2011

    a very useful study on CRO, thanks for this info

  • seetharaman
    September 23, 2011

    Hi Ankit go through the wiki site full of details.
    http://en.wikipedia.org/wiki/Oscilloscope

  • ankit kumar
    September 23, 2011

    i need complete information in cro & function of cro.

  • February 2, 2010

    love the pic of stevy wonder ……(wtf)

  • September 30, 2009

    i need CRO FUNCTION… and how i can to calibrate to one step…

  • September 28, 2009

    Each component of the oscilloscope has very important function. If one of them fails, it will give faulty readings.

    • October 27, 2013

      u r material is so nice i want more information about cro and about picture tube and some pics of that so plz u send me quick

      • February 25, 2014

        you could have explained the function of each block

Leave a Reply to taufeeq Cancel reply

Your email address will not be published. Required fields are marked *