Dark detector circuit

jacky November 10, 2011 30 Comments

Description.
The dark detector circuit shown here can be used to produce an audible alarm when the light inside a room goes OFF. The circuit is build around timer IC NE555. A general purpose LDR is used for sensing the light. When proper light is falling on the LDR its resistance is very low. When there is no light the LDR resistance increases. At this time the IC is triggered and drives the buzzer to produce an alarm sound. If a transistor and relay is connected at the output (pin3) of IC1 instead of the buzzer, electrical appliances can be switched according to the light.

Circuit diagram with Parts list. 

 dark-detector-_circuit.JPG

Notes. 

  • The LDR ,R4 can be any general purpose LDR.
  • The circuit must be assembled on  a good quality PCB or  common board.
  • The circuit can be powered from a 9V PP3 battery.
  • The POT,R3 can be sued as a volume controller.
  • Mount the IC1 on a holder.It will make replacements easy.
Comments
  • Ninette de Wet
    August 12, 2015

    Hi

    I have to get the Dark detector circuit for my sons elektrical klass. Where can I bay one?

    Thank you.

    Ninettte

  • Robin
    April 5, 2015

    Dear sir,
    In this circuit, you used 1000pF capacitor. Is the capacitor CERAMIC or ELECTROLYTIC?
    If I use 1kilo-ohm resistance instead of the 1k-pot, will the circuit function?

  • sandhya
    October 14, 2014

    can we use duracell battery instead of PP3 battery..??

  • Jessa
    September 9, 2014

    Sir, mine always sounds whether there is light or there is not. PLEASE HELP

    • seetharaman
      September 11, 2014

      May be your LDR is not OK with sufficient range. Try increasing the value of R1 from 100 k to 220 or 470 k, if it is still not become alright try by replacing LDR with different make or diameter.

  • nayan
    April 29, 2014

    sir, how the circit
    turn off

  • francis zarf
    July 10, 2013

    excuse me sir.. what pin of the relay should be connected to pin 3. and also where will i connect the diode before placing the relay.. thank you

    • francis zarf
      July 10, 2013

      or i should say instead of the diode ..what transistor is needed to place before the relay?

  • m.ahsan
    May 23, 2013

    muhamad ahsan;
    i realy don’t know about this project but i love to hear the voice of buzzer.

  • seetharaman
    May 2, 2012

    Hi Kiran you can. you may have to slightly alter the value of R1. the sound from the Buzzer will be very low.

  • kiran
    May 1, 2012

    hi can i use a 6 volts 4.5ah battery?

  • December 29, 2011

    thank u very much sir.’;

  • Seetharaman
    December 28, 2011

    Hi arc 104 is 0.1uF (100,000PF) 102 is the correct capacitor. Since the capacitor value is quite high the IC generates squarewave output. Reduce capacitor C1 value and add a 100uF 16volt capacitor across the relay to improve further.
    There is no need for any additional transistor to drive the relay as this IC is capable of 200mA drive output.

  • December 28, 2011

    susan, a relay is a switch operated by electricity. relays can be driven with a range of 6-24 volts direct current @0.5-2 amperes. the coils of the relay is where you plant the power;.’ you can connect the polarities of the power supply to the coils either way;’ relay, like other switches is classifies by their poles: SPST, SPDT and DPDT. mainly, it is an electromechanical device which is also known as electronic switch;.’

  • susan
    December 27, 2011

    what is relay?

  • December 11, 2011

    i tried the design as well and i used a 104j mylar cap for c1 1000pf. i did not find a 1m resistor so i used a 1.2m and connected a relay w/c could be driven with a supply from 8-12v i planted the diode across the relay coils yet with or without the presence of light, the relay still goes crazy. it simultaneously switches on and off and i never planted the pot. i even cut off the ldr and i get same results. sir, pls help. what could possibly went wrong?

  • manu
    December 3, 2011

    which transistor should be used to connect relay??

  • aditya
    November 20, 2011

    hey..
    what is the function of NE555 in the circuit?
    can you also tell me what is the capacitor used for?

  • RICK
    November 12, 2011

    I Like Circuit too…OVAISHAMDANI!!!!!

  • May 20, 2011

    This circt has a bit confusion … I have a simple solution for this …. Hmmm just connect ldr’s 1pin on grnd n second on ic’s 2,6 … N use a prest of 20kr n connet it between vcc n 2,6 … Dun forget to use 100nf’s ceramic capacitor on pin 5 ……… It will really work … I tried

    Ovais hamdani

  • May 16, 2011

    I used this circuit as a security system . 555 ic is great . I made lot of projects on that … Nw m doing diploma n just want to learn assembly language … If u have any curies plz ask to me i like to talk on elctronics … Search me on fb ‘hamdani ovais’ iz my username hope sme1 ll contact to me … Ovais

    • sadar
      April 14, 2013

      i dear i wanna make a human detector circuit by using 555 ic can u help me

  • kirk lee
    April 7, 2011

    hi is this working?

  • Seetharaman
    September 28, 2010

    Hi Subham you can use in both ways. light activated / dark activated by interchanging the no / nc contacts of the relay.

  • SHUBHAM
    September 28, 2010

    i think it is like light activated switch. . . . . . bcoz when we connect to relay (NC) it acts like a dark activated switch. . . .isn’t it? ? ? ?

  • seetharaman
    May 14, 2010

    Hi Abdullah NE555 can drive up to 300mA load. So you can use a power relay in the place of Buzzer remove variable resistance volume control donot forget the freewheeling diode across the relay coil. and connect any load through its contact. When you cover LDR the resistance will go high and voltage at Pin 4 will go high the out put of NE555 will go high hence the relay will come on, you may use an LED with 1K resistance in series in parellel to the relay as an indication..

  • abdullah
    May 14, 2010

    hi sir
    iremove the buzzer and i put transistor , RLL and light

    note : the light is on and off when i coverd the ldr ( no light high ressistor

  • Mylamae
    March 7, 2010

    What are the possible transistor and relay that can be replaced instead of the buzzer?

  • admin
    January 11, 2010

    yes

Leave a Reply to RICK Cancel reply

Your email address will not be published. Required fields are marked *