Fire alarm circuit

admin January 21, 2014 127 Comments

Description.

Here is a simple fire alarm circuit based on a Light Dependent Resistor (LDR) and lamp pair for sensing the fire. The alarm works by sensing the smoke produced during fire. The circuit produces an audible alarm when the fire breaks out with smoke.

When there is no smoke the light from the bulb will be directly falling on the LDR. The LDR resistance will be low and so the voltage across it (below 0.6V). The transistor will be OFF and nothing happens. When there is sufficient smoke to mask the light from falling on LDR, the LDR resistance increases and so do the voltage across it. Now the transistor will switch to ON. This gives power to the IC1 and it outputs 5V. This powers the tone generator IC UM66 (IC2)  to play a music. This music will be amplified by IC3 (TDA 2002) to drive the speaker. Resistor R6 is meant for protecting the transistor when R4 is turned towards low resistance values. Resistor R2 and R1 forms a feedback network for the TDA2002 and C1 couples the feed back signal from the junction of R1 & R2 to the inverting input of the same IC.

The diode D1 and D2 in combination drops 1.4 V to give the rated voltage (3.5V ) to UM66. UM66 cannot withstand more than 4V.

CircuitsToday has a list of 4 books for electronics enthusiasts who are looking for a better chance to learn the basics and getter a better practical insight of the subject. These books are written by authentic authors like Forrest M Mims, Charles Platt and so on. You can read their reviews and buy them online here:- 4 GREAT BOOKS TO LEARN BASIC ELECTRONICS.

Circuit diagram with Parts list.

Fire alarm circuit

Notes.

• The speaker can be a 32Ω tweeter.
• POT R4 can be used to adjust the sensitivity of the alarm.
• POT R3 can be used for varying the volume of the alarm.
• Any general purpose NPN transistor(like BC548,BC148,2N222) can be used for Q1.
• The circuit can be powered from a 9V battery or a 9V DC power supply.
• Instead of bulb you can use a bright LED with a 1K resistor series to it.

Power supply for the circuit.

A well regulated power supply is essential for this circuit because even slight variations in the supply voltage could alter the biasing of the transistor used in the fire sensing section and this could seriously affect the circuit’s performance.

9V/500mA power supply circuit

A regulated 9V/500mA power supply that can be used for powering the basic fire alarm circuit and its modified versions is shown above. Transformer T1 is a 230V primary, 12V secondary, 500mA step down transformer. D1 is a 1A bridge which performs the job of rectification. Capacitor C1 filters the rectifier output and C2 is the AC by-pass capacitor. IC1 (7809) is a 9V fixed positive voltage regulator. The output of the rectifier+filter section is connected to the input of 7805 and a regulated steady 9V is obtained at its output. S1 is the ON/OFF switch. F1 is a 500mA safety fuse.

Relay version of the circuit.

Here the above fire alarm circuit is modified to operate a relay when the fire breaks out. The usage of relay makes the circuit able to switch high power warning devices like alarms, bells,beacon lights etc that operates from the mains.

Relay version of the circuit

Two additional transistors are used with the basic fire sensing circuitry (consisting of Q1, R4, R5 and L1) to attain the target. Whenever the fire breaks out the transistor Q1 is switched ON. The collector voltage of Q1 drops to 0.2V and the transistor Q2 gets switched OFF. This makes the collector voltage of Q2 rise towards 9V and this result in the switching ON of transistor Q3. The relay connected at the collector of Q3 is activated and the load connected through the relay contact is driven. Resistors R7 and R8 limits the collector current of Q1 and Q2 respectively. D1 is a freewheeling diode which protects Q3 from the voltage spikes induced when the relay is switched. Resistor R9 controls the base current of transistor Q3 (2N2222).

Comments
• ike
July 13, 2015

I need an equivalent to um66 please

• April 17, 2015

that is very nice circuit diagram infact iam doing aproject which more related to it and i would to request you to send me “a fire alarm system with a sprinkler water circuit diagram” based on LDR,urgent pliz

• Wajahat
November 20, 2014

please can you help me for the relay version of the circuit through the email.

• October 21, 2014

GENERALLY THIS CIRCUIT DIAGRAM HAS SIMPLIFIED THE SMOKE DTECTOR

• May 6, 2014

plz tell about the connections through mail am waiting

• sohail
May 6, 2014

what the apparatus of this circuit or give detail how can connection between the apparatus

• nilesh
April 22, 2014

why capacitor is connected in series with speaker while circuit is run by dc input…..

• Seetharaman
April 22, 2014

The TDA2002 IC pin no4 will be at half the power supply (say around 4.5 volts in the above circuit) to avoid this DC flowing through speaker a blocking capacitor is used such that only the audio signal present at Pin no4 alone is fed to the speaker.

• nilesh
April 24, 2014

thanks a lot…. but what is the function of capacitor c2 which is in series with speaker

• Seetharaman
April 25, 2014

Function of C2 alone explained in my reply.

• Shreysa
April 5, 2014

Guys is it working?????

• Talaviya Mehulbhai Balubhai
January 3, 2014

I like this information and my problem why rasister connected in circuit example:-R6 1K but why not connected 5K

• Bini
December 14, 2013

I like this project.I suggested this one to my partner in mini project lab.But I also need the project report

• Smith Watson
March 14, 2014

Hey Bini did u get the project report for this circuit. It wil b great if u help me with it.. Thanks..

• foxknu
December 13, 2013

hi, can anyone tell me what to use as a substitute for um66?? It doesnt exist in proteas…

• amira
November 13, 2013

can u suggest any other ic to replace TDA2002 ,as TDA2002 does not exist in proteus software for my circuit simulation …thank u for ur help

• Seetharaman
November 15, 2013

Hi Amira use LM386 or simulate any opamp

• Forever
October 7, 2013

Hi. I just want to know what would happen if you remove the um66? or if there are any substitute for um66

• ee student
August 26, 2013

how if i still want the speaker as the output but at the same time want relay in my circuit?i’m doing this as my project

• July 22, 2013

sorry i am ask about the function of relay of this alarm circuit…it will effect if we do not make the relay for the alarm circuit

• July 4, 2013

I like this circuits.

• Michael Zurg
May 3, 2013

Thank you so much for this amazing circuit .
This site is breathtaking.

I want to use a Silicon Controlled Rectifier (SCR) instead of
NPN Transistor . What changes should be made to the circuit in this case?

Email me ur recommendation or reply to my comment .

Thanks guys.

• March 19, 2013

hii,
Guys i am going to make the fire alarm project.and i have no large idea for make this project. so i requested to all the internet users and you have any information of this topic so please share me yours information and help me this project.
thanks
Reply

• sulthana parvin
March 8, 2013

I WANT A PROJECT RELATED TO THE USAGE OF DISPLACEMENT SENSOR IN TRANSPORT
WITH CIRCUIT DIAGRAM

• December 24, 2012

Nice work……

• Prosenjit
December 20, 2012

For the power supply circuit, what is the model of the diode that can be used.

• S.A.Warsi
December 3, 2012

Wow,its awesome,they have to mention steps of construction with the help of video.

• jojo
December 3, 2012

Thank you Warsi. We will try to develop videos soon.

• October 15, 2012

hi,
Guys i am going to make the fire alarm project.and i have no large idea for make this project. so i requested to all the internet users and you have any information of this topic so please share me yours information and help me this project.
thanks

• John terry
October 17, 2012

vikki am also doing my project on fire alarming .. if you have any information share with me .. thanx sis

• doreen iortsor
August 8, 2012

Please i need an alternative for the um66 since it is difficult to find. I wil appreciate if you can help me out because this is my project topic. Thanks.

• seetharaman
October 17, 2012

Hi Doreen you can use electronic peizo alarm from Pin 3 IC1 and 2 by observing the polarity through 100 ohms resistance feed the junction of Piezo buzzer and 100 ohms resistance to Pot R3.

• August 2, 2012

i am going to make a project on the fire alram so i want that you should guid me to make this project. i am in confusion that what requriment is for the fire alram so please help. i need to submit this project on next week. i hope that you will short out my problem.

• Abdulrahman f.c.e(t)bichi kano
July 29, 2012

Helo guys am this project now.and i ned detail information on this components use in this project? Thanks alot it urgent pls

• Seetharaman
June 16, 2012

Hi John you can use 4nos of 1N4007 in bridge formation. (use 1N4007 for each diode shown in the bride circuit with correct polarity)

• john
June 15, 2012

alternative for 1A bridge in power supply ??? thanks

• Olawale kabir
April 21, 2012

please i dont no if there will ba an alternative for UM66 in fire alarm circuit please help me it is orgent please. this my mail (olawalekabir1@yahoo.com )God bless u
.

• amarjot
April 1, 2012

Iam not able to locate a circuit which tells me the wiring of an industrial smoke and heat detector system
can all detectors be wired in parallel/series or what tis the single line diagram illustrating this.
how many detctors can we install in one zone and how are they connected to each other ??

• abbas rezaeian rad
March 9, 2012

hi , thank you for this project , that’s very Useful ,

• Mohammed Afzal
March 4, 2012

Hi Mr Qalvin,
Am dealing with the fire alarm Installation and i have some Queries about connection of the Manual Pull station.
In our Project we are using NBG -12x Addressable Pull station and the Wiring System in the Catalogue Describes About SLC -ve And +ve of the Fire alarm Panel And the next addressable Device.
And the cable we Ordered is they have +ve and -ve wire i dont understand in the described cable which one acts a SLC Wire.

• Qalvin K
February 24, 2012

Hi guys, am a student in Electrical & Electronic Eng. Post your questions on fire alarm systems, i’ll gladly answer.

• phemmeee
May 28, 2013

pls send me the working principle of the fire alarm system

• gunashekar
January 15, 2012

We have three cherrytech made fire alaram pannel which doesn’t work even one. please help regarding rectify the problem

Thank u Regards

• January 13, 2012

I DON’T UNDERSTAND ANYTHING GIVEN IN THIS PAGE
PLZZZZZZZZ
BE ,MORE CLEAR

• abdulaqhil
January 7, 2012

hi,
iam student of electrical engineering i just wanted the information of the working of smoke detector

• pp
January 7, 2012

nice

• akash kumar meher
December 23, 2011

how can it be done with the STARTER, SPEAKER & POWER SOURCE? pls reply

• December 21, 2011

I am a studen of electrical and electronics engineering.I need a fire alarm circuit with details .

• nash
December 6, 2011

hi!i am electronic engineering student.
i need details info and circuits diagram of ‘smoke detector with auto water sprinkler’.
mail me.thank you.

• SEMAKUWA PONGEZA
November 30, 2011

Am a final year student pursuing bachelor of science in electrical engineering. Am in need of a software which i will use in simulation of my final year project on June 2012. The project deal with designing of electrical installation and fire alarm system in a seven floor building. Please post Any suggestion or advice in moprocot@gmail.com. Thanks

• nsumba geofrey
November 25, 2011

i would like to inquire if there can be another replacement for the IC UM66 because i have failed to find one please in need urgent help

• November 17, 2011

I am an electrical engineer working with COMA TRANS S.A.DOUALA CAMEROON.Thank you for this program very much god bless you. will be great full if the diagram of an electronic rectifier of an alternator of about 120kva can be sent to me thanks

• Abumbe francis
November 12, 2011

Hi am a student of electrical electronics engineering with power/machines as my option,pls i need workable power project topics,to construct as my final project.pls u can aid me by sending the topics to my email,,abumbefrancis@yahoo.com.

• MUSKAN
October 21, 2011

information is good

• abhishek
October 1, 2011

fire alarm can be made by using only the starter of the tube light…..its the simplest fire alarm ckt
it reqire 1 starter,speaker and a source of power supply

• rashid kilongola
May 12, 2014

correct,that is best way to design simple fire alarm

• seetharaman
September 18, 2011

Hi Ajay you can use standard good quality 8 ohms tweeter.

• Ajay
September 17, 2011

any alternative for 32 ohm tweeter..??

• kanika
September 8, 2011

sir,
iam doing this fire alarm as the miniproject.so, i
want brief explanation in this aspect.
pls send me on my id.
i need it urgently

• vinos
July 19, 2011

i m b.tech from the stream electronics & communication. It was my mini project. Thanxxxxxxxxxxx a lot , bcz i hv understood completely this circuit. Now i m very happy.

• sara
July 14, 2011

thanks for these information

• July 3, 2011

HAIIIIIIIIIIIIIIIIIIIIIIIIIII

• methyllx
June 14, 2011

i would like to have more information on this circuit as in the schematic circuit and how the circuit is connected…thanks

• fire alarm circuit.
May 4, 2011

Hi! i am an electrical technology student
i need some innovated projects to help…
so please i request you to send me the projects via the e-mail which given below and thank you so much!
tesfaye_assena@yahoo.com

• Seetharaman
April 30, 2011

Hi Kart it is just a smoke detector not the temperature detector. the proverb is where smoke is there fire is there. when the smoke passes through the light path between lamp and LDR, it resistance value changes it is detected by the electronics and through relay it can give alarm or the relay contacts can operate a solenoid which sprinkles water during fire.

• KART
April 29, 2011

HI I AM GOING TO TRY THIS CIRCUIT BUT I WAS WONDERING IF I COULD CORRESPOND WITH ANYONE DURING MY EXPERIMENT TO CLEAR ANY DOUBTS. I WOULD BE MOST OBLIGED IF ANY ONE COULD SPARE SOME TIME OF YOURS. I HAVE BASIC KNOWLEDGE ABOUT SOME OF THE COMPONENTS USED. IF I COULD GET THE PROJECT REPORT IT WOULD BE VERY HELPFUL.THANK YOU

• March 27, 2011

please, i need the project report on fire alarm system with automatic water sprinkler

• padmakumar
March 19, 2011

iam an ECE student plz mail the ckt diagram of “FIRE DETECTOR WITH AUTOMATIC WATER SPRINKLER SYSTEM” with project report .. urgent plz (mail not publish)

• Seetharaman
March 16, 2011

Hi Hanister any audio amplifier IC capable of delivering around 2 to 3 watts of power will do. This IC is a simple 5 lead package with heat sink tab similar to TO220 casing, easy to fit heat sink.

• Hanister
March 16, 2011

is there any replacement for TDA2002 IC for the fire alarm?

• siva sankar
February 25, 2011

hi i am an ece student
i want some new innovative projects….
so i request you to send me thr projects via email given below
email:katreddi.sivasankar@gmail.com

• subodh
January 22, 2011

hi I am electronics engineer want to know working priciple and circuit diagram of fire alarm system.Also let me know
components used in this system .Thanks

• Lacoste
January 19, 2011

hi?i’m called Lacoste and i’m in final year electronics and telecommunication engineering.i want to do my final project on fire alarm detector,can u plz send the report for fire alarm,and some informations.thx God bless u.

• NITIN
December 19, 2010

HI, I M A STUDENT OF ELECTRONIC I WANT TO INFORMATION ABOUT FIRE ARAM THEORY,CONCTRION,WORKING SO PLZ,U WILL SEND ME INFORMATION OF FIRE ALARM

• Franklin
November 25, 2010

hello, thanks 4 ur efforts. pls i need you 2 send me the details of this Fire alarm and 2km fm transmitter:how they work and all the principles involved. i want to do it for my final year project

• Seetharaman
October 26, 2010

Hi Ban it is a pentawatt package IC. But you can use any audio IC here with suitable PCB. TBA810, LM386, TDA2822, TBA820, any chip which can work with 9 volt and gives an audio output of 1 to 5watts to 8 ohms speaker.

• ban
October 25, 2010

is there any ic to replace tda2002

• Afeef
October 25, 2010

is their any circuit for fire alarm using only one ic..

• JD
October 8, 2010

hiiiiiiii
plz upload pcb layout of this ckt plzzz…
i need it urgently…..
thxxxxxxxx
🙂

• TUNDE BABAJIDE
September 22, 2010

THANKS FOR THIS TV TRANSMITTER, BUT I NEED THE CIRCUIT THAT CAN GO UP TO 7KM THANKS

• sayyed muzaffar
August 28, 2010

Hello I am an Electrical Eengin I need some Projects especially Automatics, sensing & control circuits please. P.O.Box STAR ELECTRONICS BHIWANDI DIST THANE M.S INDIA
Pin 421302,
EMAIL: automation.group@rediffmail.com

• seetharaman
August 24, 2010

Hi Shubham you can use. the light should be always falling on the LDR R5 whenever smome passes between light and LDR the light ray will get interrupted and the alarm will get activated.

• Shubham
August 23, 2010

is it possible to use light activated switch for this purpose. .

• seetharaman
August 22, 2010

Hi Timmy you can use NE555 oscillator in place of UM66.

• August 19, 2010

pls i need another ic of fire alarm not TDA2002

• Timmy
August 16, 2010

which Ic or component can i make use instead of UM66 in a fire alarm circuit please I need the reply B=before 24hrs.
thanks God Bless

• Androux
August 16, 2010

which Ic or component can i make use instead of UM66 in a fire alarm circuit please I need the reply before 24hrs.
thanks God Bless

• Androux
August 16, 2010

which Ic or component can i make use instead of UM66 please I need the reply B=before 24hrs.
thanks God Bless

• August 15, 2010

please i need a circuit diagram and guidelines on fire alarm system

• August 15, 2010

pls i need a good crcuit diagram and guild lines on how to build it

• rohith
August 10, 2010

haii am an ectronics student i want to know more about fire alarm so plz send me detail report of this subject .plz heip us.

• seetharaman
August 2, 2010

Hi Syarief this fire alarm is based on smoke detection principle. A light beam falls on LDR, so its resistance is low hence Q1 cannot conduct. once smoke obstructs the light, the intensity of light falling on LDR reduces hence its internal resistance increases. Q1 gets the bias inturn regulator IC1 gets the supply. Regulator IC feeds the supply to tone generator IC its out put is amplified by TDA2002 ic Hence the loud music from the smoke detector indicates that there is smoke. but smoke is normally due to fire.

• syarief
August 1, 2010

hye…im a student of electrical and electronic engenering..can u send me your fire alarm report..i need the detail..tq..

• yannick noah
February 3, 2010

hi,i m verry happy for your support provided ,so ,i’ll like to get all notes concerning fire alarm circuit ,in oder to improve my reseach .thank u

• saheed shittu
December 21, 2009

please,i need a digital calendar circuit diagram project that show days, date,months and years, using discrete components with its operation principle and detail about circuit diagram.send it to my e-mail.thank you very much.

• sarmad
December 11, 2009

helo i am a std electronics eng pls send me the whole description of fire alarm so i can built the project pls

• raza
December 10, 2009

hey i implement this circuit today but i was failed to do it properly..!there was a little beep in the beggning but then it stopped.can any body send me schematic diagram of this Circuit?

• admin
December 10, 2009

You need to calibrate this circuit before using. Adjust the POT and try again.

• om prakash
November 28, 2009

hi,i am a student of electronics . please send me your project report on fire alarm .i really want 2 study that ..so plzz..e-mail me ..

• November 20, 2009

sir/ madam,

I would like to know abt the names & authors of any text book that contains all electric/electronic circuit concepts.

V.Chandran

• kaleem
November 13, 2009

kaleem_butt@hotmail.com, plz guided me for making that circuit
thanx

• kaleem
November 13, 2009

hello sir, i m electronics engineer from pakistan, i want to make a circuit for ups who’s capacity should be atleast 1000watts.
Regards……..kaleem butt
cell # 00923457866765

• demo lynn
November 9, 2009

hi, i m an electronic student, i m finding the fire alarm system using IC CD4049, so i would like you to send me some information on how to design a smoke sensor, i m doing my project now & wanna do better fire alarm system, pls send me some details,it’s very important bcauz my presentation is on Nov 11, 2009, waiting ur reply
thx

• olaiya shola
November 8, 2009

Hi, am a student and i want to do this project . plz i want all the details about this project.thanks

• mubasahr
October 27, 2009

hi this is mubasahr i whould like to make a circuit which is time dependent like when we turn on the electric supply alarm will turn on only for 20 seconds and after 20 seconds alarm turn off

• Azel
October 21, 2009

Is it possible for me to have some more and relevant informations about the two transister siren, pliz

• amaal
October 14, 2009

hi, am a student and i want to do this project so plz i want all the details about this project

thants

• amaal
October 14, 2009

Dear Sir/Madam
I am an electronic student and i would like you to send me some information on how to design a smoke alarm sensor.
Very Important ( Please do not publish my email)
Thanks

• M.Sri Lisha
October 5, 2009

Industry or home already has lights. So does the LDR gets affected and what is the role of LDR. Smoke alarm using LDR and bulb and preset what is the significant role of ecah. Please mail to my email-id.

• […] Source: Smoke Detector for Fire Alarm […]

• neo
September 5, 2009

can u please provide me with the circuit diag. of the detector which includes diff another alarms along with the fire alarm….plz mail me…

• kev
August 31, 2009

Dear Sir/Madam
I am an electronic student and i would like you to send me some information on how to design a smoke alarm sensor.
Very Important ( Please do not publish my email)
Thanks
Kev

• ollydee
June 23, 2009

Pls I need 1000watts and 2000watts comprehensive circuit diagram for an inverter/ups. Thanks. God bless you.

• twits4twats
June 17, 2009

Sagar
Yes you can if you so desired. It would be a bit pointless though as the purpose of using a pot and not resistor is so that you can adjust the signal.

• mansoor
April 29, 2009

thanks sir i want’s that it’s my requared for my project.

• April 22, 2009

Can we use a resistor insted of pot?

• April 19, 2009

Plz i want to build a 2000Watts inverter pls send me the circuit diagram and the rating of the components required to my email address.which is geracotin2000@yahoo.co.uk. thanks.

• admin
April 19, 2009

i am working on it

• March 30, 2009

Nice easy fire alarm circuit and its operation is simple.I like the circuit and expect i do it.

• sudipto
March 18, 2009

what should be the value of the ldr?? or its range??

• admin
March 28, 2009

any general purpose LDR will do

• yashar
March 1, 2009

i am an electrical/electronic student,and i am very good at reading circuit and constuction,please i want you to send the fire alarm circuit that made by micro .

• February 28, 2009

hi there! i want 2 build a magnetically levitation train. can u send me more details about the construction. i want 2 use solenoid and permanent bar magnets. hoping 2 recieve it in my mail provided 2 u. thanx

• Low
February 11, 2009

Any replace ment for UM66 and TDA2002?

• Christian Ehifoh
January 30, 2009

i am an electrical/electronic student,and i am very good at reading circuit and constuction,please i want you to send the fire alarm circuit and its working principle,so i can construct one.thanks.hoping to recieve it in my mail provided to you.

• January 11, 2009

Hello I am an Electrcal /Electronics Eengineering Student, Ineed some Projets espeially Automatics, sensing & control circuits please. P.O.Box 7136 Bompai, Kano Nigeria.

• ISAAC
July 18, 2008

is there any new upgraded circiut on fire alarm circuit