Mains operated blinking LED

jacky January 18, 2011 20 Comments

Description.

The circuit diagram of a blinking LED that can be operated from the mains supply is shown here. The working of this circuit is as follows. When mains power is switched ON the capacitor C2 charges through resistor R1 and diode D1. When the voltage across the capacitor becomes greater than 32V ( break over voltage of diac DB3) the diac conducts making  the LED blinks and  capacitor C1 discharges through the LED.This cycle repeats again and again .

Circuit diagram.

mains operated blinking LED

Notes.

  • 230V is potentially dangerous , be very careful while handling this circuit.
  • The timing  of this circuit depends on resistor R1 and capacitor C1.
Comments
  • bindu sree
    December 2, 2015

    If we want to place more than one LED….? Without changing the circuit and wattage of components can we increase the number of LED’S ?

  • Amit
    October 22, 2013

    in the main operated LED blinking ckt, where is the capacitor C2 is used according to your ckt

    • Seetharaman
      October 24, 2013

      Hi Amit read it as C1. There is no C2.

  • suneetha
    October 20, 2012

    sir,

    i need a circuit which is main operated and which can glow 100 led’s of 3 colors in total 300 led’s alternatively.

  • October 6, 2012

    Sir. I need to know the application and advantage of main operated blinking led……

  • August 11, 2012

    Thanks for posting this, but I would like more of an explanation of what’s going on here. Are there any more in depth instructions on how this works?

  • Wayne
    February 19, 2012

    I have a 230vac compressor in my garage. When I need to use it, I turn on the master switch. If the tank pressure is <85psi, the pressure switch closes, energizing the compressor. When tank pressure reaches 135psi, the pressure switch opens and shuts off the compressor. When I am done, I usually forget that the master is still on. Approx 2-3 days later, when the pressure drops, the compressor comes back on unattended. This circuit would remind me to turn off the master switch when I am through. The LED I'd like to use is Allied Electronics Stock #70015427. I aquired quite a number of these from a project years back and they are quite visiable even in direct sunlight.

  • Athira Krishna.g
    February 13, 2012

    sir, may i know the advantage of this ciruit??

  • Wayne
    January 9, 2012

    I would like to use a LED bulb which is actually 6 red LEDs molded to a bayonette base used in 12vdc circuits. Can you suggest an appropriate value for R2 and would it still be 1/4 watt? I really don’t wish to ‘experiment’ with 230VAC

  • Edgardo
    December 17, 2011

    Hi, Seetharaman,
    Thank you very much, this is a great help.
    More power..

  • seetharaman
    December 16, 2011

    Hi Edgardo R1 is 2 watts and R2 is 1/4 watt

  • Edgardo
    December 16, 2011

    hi admin,
    May I know the wattage ratings of resitors?(R1 and R2)

  • May 5, 2011

    i make one of this and it’s warkin fine
    thanks duud

  • Mwiti
    July 17, 2010

    Thank you for you reply.

  • seetharaman
    July 16, 2010

    Hi MWm you cannot use a trac in place of Diac. diac is nothing but two zener diodes connected back to back its voltage lie between 27 and 33. you can use two 24volt zeners back to back.
    The circuit is connected to phase and neutral

  • MWITI
    July 15, 2010

    can one use a triac in place the diac, and is the circuit terminals connected to both live and neutral wire or to live wire alone?

  • RUCHIT
    July 5, 2010

    YA SEETHARAMAN U R REALY RIGHT.

  • seetharaman
    July 3, 2010

    Hi friends through 47K 5mA current is available for C2 to get charged once it is charged to 32volt approx(depend on the diac sample) the diac will conduct and through 270ohms LED will draw current plused current drain can reach 100mA. The capacitor will get discharged instantly hence you get a blink from the LED. the capacitor gets discharged and ready for the next cycle.

  • July 2, 2010

    47k is sufficient for R1???????

  • Ram Mohan S
    July 2, 2010

    From the above circuit it looks like the effective voltage across the diac, the resistor R2 and the LED is 32 volts. Basically this will be the effective voltage across the resistor R2 as the other 2 component doesnt have potential drop when conducting. Would the resistor hold that much current and will the LED sustain that amount of current? Kindly let me know.

Leave a Reply to Pushpitha Cancel reply

Your email address will not be published. Required fields are marked *