Melody Generator using IC UM66

jacky April 11, 2011 25 Comments

Melody Generator Circuit

Description

Here is a simple melody generator circuit you can make using an IC.The  UM66 series are CMOS IC’s  designed for using in calling bell, phone and toys. It has a built in ROM programmed for playing music. The device has very low power consumption.Thanks for the CMOS technology.The melody will be available at pin3 of UM66 and here it is amplified by using Q1 to drive the speaker.Resistor R1 limits the base current of Q1 within the safe values.Capacitor C1 is meant for noise suppression.

Notes

  • Power supply  must be between 1.5V & 4.5V .Do not exceed 4.5 V.
  • Speaker can be driven with external NPN  transistor.
  • Melody begins from the first note if power is reseted.
  • Assemble the circuit on a good quality common board.
  • If transistor HE8050S is not available use any NPN transistor like BC548 or 2N2222.

Circuit Diagram

Melody Generator Circuit using UM 66 IC

Melody Generator Circuit

UM 66 IC – Data and Specifications

UM 66 Data Sheet with specifications

UM 66 Data

We have other Tone Generator circuits that you may like; Take a look:

1. Police Siren

2. Ding Dong Sound Generator

3. Two Transistor Siren

4. Whistle to Beep Circuit

5. Touch Controlled Musical Bell

Comments
  • mg
    June 24, 2015

    What can be done to strengthen the multiplier circuit? Amplification؟؟؟

  • February 28, 2014

    sir,please give me working of um66 ic and block diagram and pin identification in ic

  • yogananda
    May 16, 2012

    i want the full expansion of UM66

  • keke
    August 18, 2011

    can ic555 timer be used in water level indicator with alarm to generate tone? if yes, can you help on how to substitute it with icum66.

  • francis
    August 18, 2011

    I have searched for icum66 in the market but cannot find one. please can i get a substitute?

  • Seetharaman
    May 1, 2011

    Hi Sunil It is manufacturer’s product ID. C1 is used to decouple power supply to avoid inter-modulation between output and IC. If you get a distorted sound you can add 100uF electrolytic capacitor in parallel to C1

  • May 1, 2011

    sir , i want that what does 66 indicates in UM66.
    Is capacitor helps in sound suppression in this circuit?

  • krishna
    February 20, 2011

    sir, i want to know about the purpose of capacitor in this circuit and why we connected capacitor in parlell of circuit give reason

  • elkin
    November 14, 2010

    Hello
    I cant get that circuit in digikey. Where can i buy
    Which is the nte replacement

  • shailja
    September 29, 2010

    please sir can you give me informatio regarding working and construction for my project

  • manohar
    April 28, 2010

    sir, i’m b.tech student i would like know working and storing own music by using UM 66

  • twits4twats
    February 7, 2010

    is it possible to store our own created music into um 66 if yes , how to store it… what circuit can be used. if not can any one tell me a nice way to “Design a circuit to create, play and save ringtones”

    Vignesh

    Like Admin has stated, UM66 is designed and manufactured with those melodies. You can not reprogramme it. You need a voice recorder circuit interfaced with a amplifier circuit.

  • vignesh
    January 10, 2010

    is it possible to store our own created music into um 66 if yes , how to store it… what circuit can be used. if not can any one tell me a nice way to “Design a circuit to create, play and save ringtones”

    • admin
      January 11, 2010

      It is not possible to store our own music in UM66.
      I will add a voice recorder circuit soon.

  • Seetharaman
    December 23, 2009

    UM66 is a 3 pin melody device. once the supply is given to pin 1 & 2 it will give continuous audio out put at pin3, which is not sufficient to drive a loud speaker, hence an additional direct coupled amplifier is added to drive a small speaker.

  • ananth
    November 6, 2009

    i want data sheet about the working of um66?

  • abdulsalam
    August 5, 2009

    i want the electronic copy (write up document) of this circuit by friday to complete my project work. it will help if you guys will sent every thing about this circuit

  • shyaman
    June 2, 2009

    Dear sir,

    could you forward me a 30second sound circuit that activated by another speaker out(alarm clock)
    Thanks
    shyaman

    • admin
      July 1, 2009

      by slightly modifying this circuit you can get the one you need.
      http://www.circuitstoday.com/whistle-to-beep-circuit
      (tips: modify the band pass filter, vary the mosostable’s delay to 30S)
      If you cant do it yourself, comment here . i will give you the modified circuit.

  • Brandon
    November 19, 2008

    Where can I find the UM66 IC to purchase?

  • mic
    March 15, 2008

    hi

  • mic
    March 14, 2008

    pls

  • Anonymous
    March 5, 2008

Leave a Reply to vignesh Cancel reply

Your email address will not be published. Required fields are marked *