Puff to OFF LED circuit.

admin November 11, 2011 28 Comments

Descrption.

This is a simple circuit in which the glowing LED can be switched OFF just by a puff. A condenser mic (M1) is used to sense your puff. When the push button S1 is pressed, the transistors Q2 and Q3 wired as latching pair gets activated and drives the LED to glow. The LED remains in this condition. When you puff on the condenser mic, the sound pressure is converted into a voltage signal at its output. This voltage signal will be amplified by the transistor Q1.Since the collector of the Q1 is coupled to the emitter of the latching pair, the pair will stop conducting when ever there is a signal from the condenser mic due to puffing and the LED will go OFF.  The push button switch S1 has to be pressed again to switch the LED ON.

Circuit diagram with Parts list.

puff-top-off-led.JPG

Notes.

  • The circuit can be powered from a 3V battery.
  • The M1 can be a general purpose condenser microphone.
  • The switch S1 can be push button switch.
  • The circuit can be assembled on a good quality PCB or common board.
  • Instead of the LED, you can also try a low power 3V bulb.
Comments
  • sandesh
    July 16, 2015

    this project is really very good.. mine its working good.. i have connected a relay across the led to use for 220 v light bulb..thankyou.

  • dhana
    September 13, 2014

    the circui t donot work, the led will be on

  • Tajon
    January 20, 2014

    is there any way to replace the LED with say a fan and the circuit operate the same?

    • guhan
      April 8, 2014

      yes it will work

  • samiran
    January 12, 2014

    Please tell me the values of the condencers/capacitors as 10uf….v.
    Thanks.

  • Nouman Nazir Malik
    January 1, 2013

    Made it its working use 1uF at C1

    • shiraz
      April 22, 2013

      kindly send me details of this CIRCUIT ON MY EMAIL
      thanking you sooo much
      please dear nouman malik

      • Marvin
        October 7, 2014

        Can i see your circuit too? badly needed 🙁

        • Marvin
          October 7, 2014

          I need it now 🙁

  • November 15, 2012

    Hi, in the circuit shown in the URL, i need to have 3 or 5 LED glowing instead of 1. kindly help me with the modifications.

    Regards
    Nagaraj

  • Jimmy Svensson
    October 29, 2012

    Why does the latch turn off when q1starts conduct?

  • Jai
    April 11, 2012

    if the LED is not switching of try using C1 as 1uF instead of 100pF … worked for me…

  • seetharaman
    February 24, 2012

    Hi Taimur we will try to publish a suitable circuit.

  • Taimur
    February 23, 2012

    Can somehow by any means instead of using the LED , I may use this circuit for a 40W bulb? what modifications will I have to do for it ?

  • Seetharaman
    January 25, 2012

    Hi Aniket Disconnect D1 and C2 and switch on power, LED should not light up. Now push S1 it should come on. Releasing S1 should turn off if this operation is OK, check for the polarity of C2 and D1.

  • Aniket
    January 23, 2012

    the led doesnt turn off !!!

  • aljon
    December 7, 2011

    hi!
    Why does the led turns off when the latching pair stops conducting. Even though the switch is still connected.

  • Shivakumar
    August 23, 2011

    Hey. . . I hav the similar problem . . plz help on this. it’s our 1st mini project, and i don’t wanna fail in that. . . . . .

  • August 12, 2011

    for admin. i was try it. but, it doesn’t work. LED only “on” if i staying to press the switch, and led’ll “off” after i relase it. ECM is unfunctionable to off led. can you help? tks

  • August 8, 2011

    rangkaian yang unik. bagus, perlu dikembangkan itu.

    the unique circuit. good, that need to improved.

  • wail
    January 1, 2011

    if there is a small changes in the value of the
    components.does it will effect?

  • kareena
    August 12, 2010

    what is the application of this circuit in day to day life?

  • Kristijan
    December 29, 2009

    can I put this circuit on a 9V battery

  • jia jalapan
    January 8, 2009

    can we ask something about the history of Puff to OFF LED circuit?

  • ThayoSoft
    September 4, 2008

    Very great circuit and very useful for my project.Continue with more interesting posts.Cheers

    • July 14, 2012

      led is not turning off when we give it puff

      • Nouman Nazir Malik
        January 1, 2013

        just check Base Collector and Emmiter

        • Condoriano
          March 20, 2014

          why does not led not turning off? what is the problem?i already checked the transistor many times but the led doesn’t turning off.

Leave a Reply to guhan Cancel reply

Your email address will not be published. Required fields are marked *