# UJT RELAXATION OSCILATOR

AIM

To design and setup a UJT relaxation oscillator.

COMPONENTS AND EQUIPMENTS NEEDED

1. UJT (2N2446)

2. Resistors

3. Capacitor

4. CRO

4. DC power supply

CIRCUIT DIAGRAM  DESIGN

Take Vp= 10 V and f =1 KHZ

Vp= η VBB+ Vd (Vd can be neglected)

VBB=15V (Assume η = 0.62)

From data sheet valley point specifications are Vv=1.5 V and Iv =4 mA and Ip= 5 mA

Combination of R2 and R4 is indicated as R.

R max= (VBB-Vp)/Ip =1 M

R min = (Vbb-Vv)/Iv =3.2 K

Take the GM of the two values R= 60 K (For this use a 100 K pot in series with 10 K

Now T =RC ln[1/(1-η)]

So C=0.004 uF (use 0.01 uF)

Use 100 Ω resistors at the two bases to provide low discharging path

THEORY

UJT is the Uni Junction Transistor. It is a three terminal device. They are: a) emitter b) base1 c) base2. The equivalent circuit is shown with the circuit diagram. So there are two resistors. One is a variable resistor and other is a fixed resistor. The ratio of internal resistances is referred as intrinsic standoff ratio (η).It is defined as the ratio of the variable resistance to the total resistance. Due to the existing pn junction, there will be a voltage drop. If we apply a voltage to the emitter, the device will not turn on until the input voltage is less than the drop across the diode plus the drop at the variable resistance R1.When the device is turned on holes moves from emitter to base resulting in a current flow. Due to this sudden increase in charge concentration in base1 region conductivity increases. This causes a drop at base1.This region in the graph is known as negative resistance region. If we further increase the emitter voltage the device undergoes saturation. So a UJT has 3 operating regions:

1. Cut off region

2. Negative resistance region

3. Saturation region

In a relaxation circuit there is an RC timing circuit. When the supply is turned on, the capacitor starts charging. When the voltage across the capacitor reaches the pinch off voltage, the UJT turns on. After discharging of capacitor ,again it starts charging, and this process continues till power supply is turned off.

PROCEDURE

1. Test the components and identify the leads of UJT

2. Switch on the power supply.

3. Observe the wave forms at bases and emitter of UJT.

4. Plot the graphs

WAVE FORMS RESULT

A relaxation oscillator using UJT was designed. Output obtained. Waveforms were plotted.

SAMPLE VIVA QUESTIONS

1. Mention any application of UJT relaxation oscillator

In triggering circuits of SCR

2. What is intrinsic standoff ratio?

See theory

##### We recommend:
• June 4, 2012

Here is the updated theory about ujt relaxation oscillator Everything About UJT relaxation Oscillator

• May 15, 2012

The Circuit diagram and principle of operation of UJT relaxation Oscillator is posted in

http://mycircuits9.blogspot.com/2012/05/ujt-relaxation-oscillator.html

• May 15, 2012

The principle of operation of UJT relaxation Oscillator is posted in

http://mycircuits9.blogspot.com/2012/05/ujt-relaxation-oscillator.html

• sravya chandra
April 9, 2012

could u pls show me the circuit diagram

January 30, 2012

Could I get the responsible Circuit Diagram

January 30, 2012

Please send me the Circuit diagram,Waveform, Resistor & capacitor data sheets for testing in lab.

• ashwini.v.patil
March 26, 2011

why ujt is considered as relaxation oscillator

• sai
July 25, 2010

please send me the circuit diagram images of electronics lab manual.i need it.

• April 29, 2009

can u show ckt images and output waveforms

• Caren
March 27, 2009

pls send me the image.. i cant read it here…

April 5, 2009

the image will be corrected soon.

• rahul
March 2, 2009

hey can i have the circuit images of respective topic .i think this make this manual more effective

• sneha
November 5, 2008

hey can u upload the images of the manual i cant acces those images i things they r being removed

• October 22, 2008

It is fabulus but Please provide power considration

• ANSHU KOUL
September 8, 2008

send me